"放大器"

返回
首页 | 功放 | 论文 | HV venti

HV venti Amplifier | 1600 W total power | 2 x 800 W @ 2ohm | A-class

Audison Thesis HV Venti 是一款双单声道立体声功放,其设计符合最高的高端标准,经过广泛的研究和开发,实现了毫不妥协的性能。这款功放代表了音频技术的巅峰,在同类产品中独树一帜。


HV Venti 的双单声道配置使用了四个同步 PWM 电源,可确保对电流瞬态做出极快的响应,从而提高音质。输入电路直到最后一级都是完全平衡的,而放大器的整个配置则通过在主板外布线来避免电磁干扰。


HV Venti 的另一项重大创新是其输出级,它基于 MOSFET-BJT 混合拓扑结构,使用分立器件来提高效率和功耗。这种解决方案可以在每个输出器件上保持较高的偏置电流,从而提高 A 级效率。


HV Venti 具有双电源功能,可将输出配置为两种模式:高电流和高功率。这种灵活性使功放能够适应所连接扬声器的阻抗和功率处理规格,根据特定需求优化音频性能。


为确保最高音质,前置放大器采用了全平衡 JFET 差分级,并为控制单元配备了输出缓冲器。此外,渐进式冷却系统可确保有源元件的工作温度保持恒定,从而对音质产生积极影响。


功放采用防刮钢化玻璃,并战略性地安装了白色、红色和蓝色 LED 灯,让您可以欣赏到其内部设计的复杂性和美感。


总之,Audison Thesis HV Venti 是一款集技术创新、优雅设计和无与伦比的音频性能于一身的功放,堪称高端移动电子产品领域的标杆。


HV venti

双单声道结构

四个同步 PWM 电源可实现极快的瞬态电流响应,并创建双单声道配置。

mosfet-bjt 混合配置

HV venti 采用独特的输出功率级拓扑结构,分立式 IGBT 由两个日立 DMOS 构成,驱动两对互补的 Sanken 功率 BJT,每个 BJT 的额定峰值电流为 30A,耗散功率为 200W。

A 级前置放大器和驱动器

它由前端前置放大器和控制单元两部分组成。整个音阶直到驱动器输出都是平衡的。电源电压为 90 V,专门用于本级和两个独立通道。独立的 150 V 电源具有热稳定和 A 类偏压功能。第一级互补 JFET 差分和第二级互补 BJT 差分的输入是平衡的。电压放大器为级联型,输出级由缓冲器驱动。

放大器技术数据

Channels 2
Class A-Class
Hi Level Input Yes
Low Level Input Yes
Digital Input No
Power supply voltage / fuse 11 ÷ 16 VDC
Idling current 4.2 A
Idling current when off 0.006 mA
Consumption @ 14.4 VDC, 2Ω, Max Musical Power 90 A
Remote IN 7 ÷ 16 VDC - 1 mA

放大器级

Distortion - THD @ 100 Hz, 4Ω, 70% Rated Power <0.05%
Bandwidth A (-3 dB, 2 VRMS, 4 Ω): 4Hz ÷ 75 kHz
S/N ratio A (A weighed @1 V): 100 dB
Damping factor A (1kHz, 4 Ohms): 80
Input sensitivity Pre-In Input sensitivity (high): 0.25 ÷ 1.6 VRMS Input sensitivity (low): 1 ÷ 7 VRMS
Total Power RMS 1600 W
Output Power (RMS) @14.4 VDC, 1% THD • 2 Ch: 400 W x 2 (4Ω)

• 2 Ch: 800 W x 2 (2Ω)

• 1 Ch: 900 W x 1 (4Ω)
Adjustable Crossover No

输入

Input Type Pre IN: L/R (ABS)
Filters Outputs Pre OUT (pre in bypass): L/R (ABS)
Filter Pass A Crossover frequencies High pass & Low pass stereo 45 - 55 - 65 - 80Hz, 12dB/oct.
Filter Pass B Crossover frequencies Lo-pass mono 45 - 55 - 65 - 80Hz, 24dB/oct.

其他

Fuse 100 A
Other Fucntions Demo mode ext. supply: 12 VDC - 600 mA ; Ext. Cap terminals: 18 VDC cap min
Weight 15 kg

尺寸

Dimension A 510 mm
Dimension B 85 mm
Dimension C 280 mm

特点

HV venti
  • 专用电路 IGBT(绝缘栅双极晶体管)。
  • 级前置放大器、中间级和驱动器。
  • 双单声道结构,具有四个同步 PWM 电源
    配置。
  • 完全采用分立元件制造。
  • 信号切换完全使用继电器。
  • 全平衡输入电路
  • 电源在单独的电路板上,以消除干扰。
  • 双电源 "功能可在大电流和大功率之间切换。
  • 偏置选择器 "功能可更改 A 级的百分比。
  • 提供高质量的分频模块。
  • 5 毫米铝制底盘,连接两侧冷却管道。

技术

HV venti
高保真音频

根据 JAS(日本音频协会 - jas-audio.or.jp)提供的 HiRes 音频定义,HV Venti 远远超出了上述 40 kHz 带宽模拟要求,可提供惊人的 5 ÷ 75k Hz(@ -3 dB、2 VRMS、4 Ω)。

HV venti
mosfet-bjt 混合配置

独特的输出功率级拓扑结构,FUNCTION 分立式 IGBT,由一对互补的日立 DMOS 驱动两对互补的 Sanken 功率 BJT 实现,每个 BJT 的额定峰值电流为 30A,耗散功率为 200W。

HV venti
双电源功能

这项革命性的功能允许用户选择放大器的输出功率配置和工作等级。

HV venti
双单声道结构

四个同步 PWM 电源可实现非常快的瞬态电流响应,并可创建双单声道配置。

HV venti
jfet 差分级

全平衡 JFET 差分前置放大器输入,带控制单元输出缓冲器。

BEYOND
THE ABSOLUTE

In the Marche region, a geographical area world-famous for the production of esteemed musical instruments, Audison started its long history in the pursuit of audio preformance perfection.

THE GENESIS OF

HV VENTI

As early as 1991, HR 100 stood out as a benchmark, bringing the Audison brand into the Olympus of Hi-End manufacturers.

HR 100 was designed to obtain the highest sound quality without compromises. Its maximum power output was its only limitation, as technology of the time did not allow this reference sound quality with massive power. Four years later the THESIS brand was created. Using the latest technology, Audison once again rewrote history on amplifier performance. In 1995 and in 1996 respectively, HV sedici and HV trenta amplifiers came to light.

THESIS and HR 100 have a strongly distinctive sound, which could not be improved in its uniqueness, but one way to try was: to merge the two projects into a single amplifier, long-held in the dreams of
Audison designers. After two years of research, with HV venti, the dream became true.

 

HR 100

HV VENTI

"THE AMPLIFIER​"

Like its predecessors, HV venti is an absolute reference product for the years to come, indelibly marking the history of Hi-End mobile electronics.

Audison_EISA_HV_venti_LOGO_web_sm

“The Thesis HV venti sets new standards in the world of car audio amplifiers. Only an extremely experienced designer could have created such an exclusive product. The six-stage power supply, the twomode
amplifier (high current, high power), the completely hi-end, discrete devices and straight sound path will be well appreciated by the musical enthusiast. But it’ s only the result of a deep reconsidering of the meaning of the mobile amplifier concept. Every part of the Thesis HV venti was a rethink, and every single
component was optimised using the most exclusive devices, solutions and materials. Every electronic, mechanical, thermal and aesthetical aspect was improved by going back to the beginning. The Thesis HV venti is the wonderful synthesis of an extraordinary engineering effort.”

logo hires

Absolute lack of compromise in achieving maximum performance, this is the mantra followed by the Audison R&D for the HV venti, a project with the following unique features.
Output power stage based on an innovative topology similar to IGBT (Insulated Gate Bipolar Transistor) but employing discrete devices.

Total void of integrated operational circuitry that, due to their
constructive technology and the low voltage level can deteriorate the signal. Their elimination allowed the engineers to work at higher voltages and with a Class biasing of the intermediate stages.

All signal commutations were treated using special relays: too
complex of a circuit would have led to longer tracks and parasitic inductances, causing signal deterioration and loss of musical information.

The whole input circuit is balanced up to the final stage “Front End”, while the amplifier’s configuration is “Dual Mono”.
In order to avoid electro-magnetic interferences, no high current is passed on the main board.

HV VENTI UNIQUE DESIGN

OUTPUT POWER STAGE

The output power stage is based on an innovative topology similar to IGBT (Insulated Gate Bipolar Transistor) but employing discrete devices.
The circuit is made from a complementary pair of Hitachi DMOS drivers, usually used as output stage devices (such as in HR100), which drive two pairs of SANKEN power BJT transistors providing each with 30 A peak current capability and 200 W dissipation.
This solution allowed the use of only two pairs of output devices,
thus permitting bias currents which necessarily have to be shared according to the number of output devices in parallel to be reduced; therefore, increasing the bias current value on every output device is possible, keeping the total current absorbed by the amplifier stable when in idling status. All this leads to the increase of the output stage to A class value.
The percentage of A Class and consequently the idling current
can be adjusted via the BIAS current diverter. As a result of the
configuration of the HV venti in Hi Power or Hi Current mode, there will be a variation of the A Class percentage and therefore of the idling current also.

CROSSOVER

To guarantee maximum sound quality, the crossover was made on a separate module supplied with the product.
Available adjustments are Hi Pass/Lo Pass 12 dB and Lo Pass
24 dB mono. Four cut-off frequencies are selectable for the filter
(45; 55; 65; 80 Hz). Although this solution is limiting compared
to a continuously adjustable cut-off, filter linearity is drastically
improved and long signal paths are avoided.

PREAMPLIFIER AND DRIVER

It is made of two groups, Front End pre-amplifier and control unit.
The whole stage is balanced up to the driver outputs. The power
supply voltage is 90 V and is specific for this stage and dedicated
to the two separate channels.
The separate 150 V power supply is thermally stabilized and A Class biasing. Input is balanced with the first stage, complementary JFET differential and the second stage, complementary BJT differential. The voltage amplifier is Cascode type with a buffer to drive the output stage.

POWER SUPPLIES

The product features two Hi power supplies for each channel
providing power exclusively to the Dual-Mono output stage.
Each channel power supply pair works in Synchro-PMW mode: an
independent circuit controls each of them. 
However, they are synchronized with one another and are designed to supply one single power source, one supplies the positive and the other the negative power. This solution allows engineers to increase the impulsive current transient response necessary to the amplifier.
Furthermore, the two pairs of power supplies were synchronized to reduce radio frequency electro-magnetic interference.
The layout featuring four separate power supplies has allowed
the use of a single powerful MOSFET for each power supply rail,
thus avoiding the paralleled configuration that is perhaps the main cause of amplifiers failures.
Each transformer and related filter inductor were enclosed in nonmagnetic metallic shells and then filled with resin.
This procedure further increases reliability for two reasons: first
of all, coils are blocked and therefore made immune to vibrations;
secondly, heat is homogeneously distributed, thus preventing any
possible overheated areas.
The resin-filled groups were then mounted onto the aluminium
thick bottom plate to allow heat to be dissipated through side
heatsinks.
In order to avoid this kind of situation, you are often forced to use
convoluted wiring which compel designers to accept compromises.
Compromise is not accepted in the HV venti. Inside the HV venti a six layer thick copper board was used to gather all output stage
return currents; the layout was created so that each current path
comes close with the return current flowing backwards. This way
the electro-magnetic fields are out of phase and nullify each other: this solution could be defined as a “balanced power supply”.

订阅 Audison
新闻通讯

隐私概述

本网站使用 Cookie,以便为您提供最佳的用户体验。Cookie 信息存储在您的浏览器中,其功能包括在您再次访问我们的网站时识别您的身份,以及帮助我们的团队了解您对网站的哪些部分最感兴趣和最有用。